[CRTech] Christian Radio Tech [MSG 84314]
[Thread Prev] [-- Thread Index --] [Thread Next] [Date Prev] [-- Date Index --] [Date Next]
Re: Heliax cable bend?
To: CRTech <crtech@crtech.org>
Subject: Re: Heliax cable bend?
From: David Benson <wn8mup@gmail.com>
Date: Sun, 18 Nov 2018 14:27:20 -0500
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20161025; h=mime-version:references:in-reply-to:from:date:message-id:subject:to; bh=1eGq2tL7owkxikSBxxm3uxJSal97eBRSIPBaFTucS6Y=; b=WvJQP7MXQNIIgXbRqeUOOazS6lu9clD3b8IM3wX4vPr2E95I86YWNX51ze4izKstfr +GKQlDwDMBiIuq/N3uGCOxBjvQbqVIIpYCf2rCQ2ahGcbZ02Zs3IhULPHhIvj5rQVUq+ Osb3JN1Q+IQsgLkKxPNPE75YQ0p75y7n2mrqvM87Z6aEkXBYxSctTzCxZ+mwacFGFLWh vpjgFjryHnoC6wZst/MvGDC7wwfbcTCypOnnBItE6Zt9hJjvmbfDp5/WA4ygIvyPJbtc hv+HDVb7GjGsb3C3zC3QHHzHPBEOyl96B3/7CB23W0WOZCLjrgYt9VlHDAeRcFm403Vq 6kYw==
In-reply-to: <CABBF47Fmm9=H8mBJ6ed3PuuRu-AdumrKfgLi078aRDuTtGQiwQ@mail.gmail.com>
References: <004501d47d17$00d86b10$02894130$@pilgrimradio.com> <CABBF47Fmm9=H8mBJ6ed3PuuRu-AdumrKfgLi078aRDuTtGQiwQ@mail.gmail.com>
Maybe make sure that section is pretty warm before trying to straighten, just my 1/2 cent worth of advice.

On Sun, Nov 18, 2018, 8:49 AM Rick Jesse <javajava56@gmail.com wrote:
Be careful. That’s a tight bend for sure

On Thu, Nov 15, 2018 at 10:11 PM Bill Hurne <billhurne@pilgrimradio.com> wrote:

Re-working RF plumbing at an installation, want to straighten a 90 degree bend near end of in 3 inch 50 ohm corrugated Heliax.    I think it is HJ8-50B, but not sure.  Existing Cable bend has about a 20 inch radius, recommended radius is no less than 30 inches.   It is working fine with the 20 inch radius and is pressurized.

 

Would I be safe to straighten the bend?   Would straightening cause damage requiring cutting off the bend and adding cable?   Of course work needs to be done while off air, just want to know how long we will be off, etc.

 

Bill Hurne
Chief Engineer
Pilgrim Radio

 

P: 775-883-5647  Ext 18


6363 U.S. Hwy. 50 East
Carson City, NV  89701

 

www.pilgrimradio.com

 

cid:f_jmhtzcok1

 

 

--
Sent from Gmail Mobile, after stopping!
References: Heliax cable bend?
("Bill Hurne" <billhurne@pilgrimradio.com>, 15 Nov 2018 19:11:38 -0000)
Re: Heliax cable bend?
(Rick Jesse <javajava56@gmail.com>, 18 Nov 2018 13:49:34 -0000)
Prev by date: Re: Heliax cable bend?
(Rick Jesse, 18 Nov 2018 13:49:34 -0000)
Next by date: Re: Heliax cable bend?
(Kevin Kidd, 18 Nov 2018 22:35:24 -0000)
Prev by thread: Re: Heliax cable bend?
(Rick Jesse, 18 Nov 2018 13:49:34 -0000)
Next by thread: Re: Heliax cable bend?
(Kevin Kidd, 18 Nov 2018 22:35:24 -0000)
CRTech.org