[CRTech] Christian Radio Tech [MSG 84313]
[Thread Prev] [-- Thread Index --] [Thread Next] [Date Prev] [-- Date Index --] [Date Next]
Re: Heliax cable bend?
To: CRTech <crtech@crtech.org>
Subject: Re: Heliax cable bend?
From: Rick Jesse <javajava56@gmail.com>
Date: Sun, 18 Nov 2018 07:49:06 -0600
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20161025; h=mime-version:references:in-reply-to:from:date:message-id:subject:to; bh=lkHFsh22f4eLQsSAjZ48H3EnNO/QKrh6Ttbj/Vq04Hc=; b=REgLZF/Jyeiu36b/8/M00BSD/Ti98Vz/3ZuV2SU1P4JSsJC3UtwuOeNOip9koCh3TU jnvxvMdlile5D/iUId5bjnVSTtHG6yrmOKWLdW2QKt3cfGpllhVe88mUsp1qE0ahcTg4 RGK0+whIeEInTs3JjDZvu1ziNhAQjGbS/efl3DPSE97qlWA6H6Lqecel3uV040SROF4n 8vl0jlA/qCAGrGDUqvGcP+BFLODxSiXLV71QEjQeLB0mkNcDxY/ctg/DfHdlrexjZJbJ e3w4yixxlhmduYq+ltQjfTPds7IDZLLNQU1YHJXBBNE3cIr0IG7BayyRN6jwPVYQ/wAS HR4Q==
In-reply-to: <004501d47d17$00d86b10$02894130$@pilgrimradio.com>
References: <004501d47d17$00d86b10$02894130$@pilgrimradio.com>
Be careful. That’s a tight bend for sure

On Thu, Nov 15, 2018 at 10:11 PM Bill Hurne <billhurne@pilgrimradio.com> wrote:

Re-working RF plumbing at an installation, want to straighten a 90 degree bend near end of in 3 inch 50 ohm corrugated Heliax.    I think it is HJ8-50B, but not sure.  Existing Cable bend has about a 20 inch radius, recommended radius is no less than 30 inches.   It is working fine with the 20 inch radius and is pressurized.

 

Would I be safe to straighten the bend?   Would straightening cause damage requiring cutting off the bend and adding cable?   Of course work needs to be done while off air, just want to know how long we will be off, etc.

 

Bill Hurne
Chief Engineer
Pilgrim Radio

 

P: 775-883-5647  Ext 18


6363 U.S. Hwy. 50 East
Carson City, NV  89701

 

www.pilgrimradio.com

 

cid:f_jmhtzcok1

 

 

--
Sent from Gmail Mobile, after stopping!
Follow-Ups: Re: Heliax cable bend?
(David Benson <wn8mup@gmail.com>, 18 Nov 2018 19:27:41 -0000)
References: Heliax cable bend?
("Bill Hurne" <billhurne@pilgrimradio.com>, 15 Nov 2018 19:11:38 -0000)
Prev by date: ETRS Form 3 Deadline
(Kevin Kidd, 17 Nov 2018 19:41:57 -0000)
Next by date: Re: Heliax cable bend?
(David Benson, 18 Nov 2018 19:27:41 -0000)
Prev by thread: Heliax cable bend?
(Bill Hurne, 15 Nov 2018 19:11:38 -0000)
Next by thread: Re: Heliax cable bend?
(David Benson, 18 Nov 2018 19:27:41 -0000)
CRTech.org