[CRTech] Christian Radio Tech [MSG 83431]
[Thread Prev] [-- Thread Index --] [Thread Next] [Date Prev] [-- Date Index --] [Date Next]
Re: RE: HT-10 Blower Motor
To: CRTech <crtech@crtech.org>
Subject: Re: RE: HT-10 Blower Motor
From: Mark Croom <markc@newmail.kinshipradio.org>
Date: Mon, 23 Jul 2018 23:01:00 -0500
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=newmail-kinshipradio-org.20150623.gappssmtp.com; s=20150623; h=mime-version:in-reply-to:references:from:date:message-id:subject:to; bh=wxHMaPyNhNVnGX5htloe1yZCFEENGF7gwHUsSNHb8uM=; b=YaYvu/4deg2Qh2uUfZ3m9IsaOUAiSb7B7lC981W+IJIxDkMOTV+lxAYOFH6TT1RrXq BhN7Iyxrlw+05+1Ba0mbIz/G4lXXzM+ubVr69DhULWVeCfm1/k58sxtAiLDOVm6B8Ll8 YimJeS+VDlAtjRimoYpLsi1ZlBBBu+oTDVqJYp5JiTbKHV3YYfJ3EQBMBfBP4KPW3zWH 1Aj9zgheG1/JArk3sMAjyx6ZtD3sqB6M2mhiyTlc2XqvcwLd3kw1WgzS7SxtFZzApHQJ a92s8bDciQoXANwVCuSoLi/2lF/2r+r6MSznZ6LLDj83BBR06xdfZfvsb/6qejBnfwbz fdPQ==
In-reply-to: <DM5PR12MB255231570ECC23D92C2A5847ED560@DM5PR12MB2552.namprd12.prod.outlook.com>
References: <DM5PR08MB2953F68F95709D3052695BA7A7560@DM5PR08MB2953.namprd08.prod.outlook.com> <DM5PR12MB255231570ECC23D92C2A5847ED560@DM5PR12MB2552.namprd12.prod.outlook.com>
The one I did recently cost me $125 or so.

Two bearings and some labor to pull and press, plus a quick test. Worked like new afterward.\

Mark

On Mon, Jul 23, 2018 at 6:25 PM, Scott Todd <stodd@kloveair1.com> wrote:

A few hundred bucks at most to get the bearings replaced at a motor shop.  Likely it’ll be done in a day or two.

 

Scott Todd

 

From: Eric Send [mailto:erics@wtcmradio.com]
Sent: Monday, July 23, 2018 2:31 PM
To: CRTech <crtech@crtech.org>
Subject: HT-10 Blower Motor

 

I have a Harris HT-10 transmitter that has a tired blower motor. I am hearing bearing noise coming from the blower. The transmitter has been in service since 1993 and I have an even older HT-10 in service at another facility. Gates Air wants almost 4200.00 for a replacement motor. The lead time is four weeks. I was able to do some research and found a vendor that will sell me a blower for 2400.00 with about the same lead time. 

Still way to much $$$$.

Here is my question for the brain trust. 
Does anyone have a spare motor sitting on a shelf that are willing to part with for a reasonable amount?
Has anyone successfully rebuilt the original blower motor?
Has anyone successfully retrofitted a different less costly blower into an HT-10? 

Eric 
WTCM Radio
Traverse City, Mi 

BLOWER 230V 50/60 HZ
3220RPM, 525CFM, 410W |
ROTRON CX33A3G (DISTR #027555 (OBS)) | 
AMETEK-ROTRON 037792 (MODEL #NC33A3G)




--
Mark W. Croom
Riverfront Communications, LLC
Yankton, SD
References: HT-10 Blower Motor
(Eric Send <erics@wtcmradio.com>, 23 Jul 2018 19:30:59 -0000)
RE: HT-10 Blower Motor
(Scott Todd <stodd@kloveair1.com>, 23 Jul 2018 23:26:00 -0000)
Prev by date: HT-10 Blower Motor
(Chris Hall, 24 Jul 2018 02:05:41 -0000)
Next by date: HT-10 Blower Motor
(Ed Trombley, 24 Jul 2018 04:25:02 -0000)
Prev by thread: RE: HT-10 Blower Motor
(Scott Todd, 23 Jul 2018 23:26:00 -0000)
Next by thread: HT-10 Blower Motor
(Chris Hall, 24 Jul 2018 02:05:41 -0000)
CRTech.org